Carrier-access Access Navigator Manual do Utilizador Página 661
- Página / 704
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Access Navigator - Release 1.8 August 2003 C-3
SNMP Interface
Carrier Access Enterprise MIB
Carrier Access Enterprise MIB
The CA Enterprise MIB (Figure C-2) provides management support for Access Navigator features not
included in the standard MIB (RFC 1213). It also enables remote management of CA products connected
via the T1 facility data link (FDL) to the Access Navigator (Figure C-1). The CA Enterprise MIB supports:
l Access Navigator system configuration settings including SNMP
l Access Navigator interface management
l DS1 management features not supported by the standard MIB
l DS0 management
l Remote device management
l Remote crossconnect management
l Remote interface settings
l Remote DS1 settings
l Remote DS0 settings
l Remote cards and slots
NOTE: The Access Navigator documentation CD-ROM includes the Access Navigator
Enterprise MIB definition file (ACCNAV.MIB) in ASN.1 standard syntax for use by network
management software.
Figure C-2. Carrier Access Enterprise MIB (top level)
iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).cac(964)
cacProducts(3)
cpAccessNavigator(3)
anObjects(1)
anSystem(1) anRemote(3)
1.3.6.1.4.1.964
Carrier Access
Corporation Products
anTransmission(2)
DS1, DS0, CrossconnectsSettings, Interfaces
- Access Navigator 1
- In this Preface 3
- Compliance 4
- Title and Risk 6
- Copyright 7
- Warranty 7
- Disclaimer 7
- Limitation of Liability 7
- Jurisdiction and Venue 8
- Warranty Product Returns 10
- TABLE OF CONTENTS 11
- Table of Contents 12
- Table of Contents 13
- 5 Physical Installation 14
- 6 Electrical Installation 14
- 7 Start Management Session 17
- 8 Provision Access Navigator 17
- 9 Provision DCS Service 17
- 10 Provision GR-303 Service 18
- 14 Alarm Clearing 20
- 16 Maintenance Procedures 22
- 18 CLI Language Reference 23
- A EOC Interface 27
- B FDL Interface 28
- C SNMP Interface 28
- Introduction 29
- Overview 30
- Features and Benefits 31
- System Architecture 32
- Access Banks 33
- Management 34
- Introduction 35
- Configuration 42
- Applications 43
- Interfaces 43
- Specifications 43
- System Clocking 44
- Signaling 44
- Management Interfaces 44
- Protocols 44
- Environmental 45
- Physical 45
- Compliance Requirements 46
- UL Requirements 47
- Ordering Information 48
- GR-303 Services 52
- DCS Services 54
- Management Architecture 55
- FDL Management 56
- GR-303 Signaling 60
- DCS Signaling 60
- P-Phone Services 70
- Standards 78
- PLUG-IN CIRCUIT CARDS 85
- Horizontal 19-Inch Rack Mount 86
- Horizontal 23-Inch Rack Mount 89
- Install Crossbars 94
- Vertical Wall Mount 97
- Ensure Adequate Clearance 98
- Prepare Plywood 98
- Physical Installation 100
- Physical Installation 101
- Electrical Installation 105
- Electrical Installation 107
- Tools and Materials Required 108
- Chassis Ground Connection 109
- REAR PANEL TERMINALS 111
- DSX-1 Cable Connections 112
- Tools and Materials 113
- Prepare DSX-1 Cables 113
- Attach Ferrite Beads 117
- PREMISES 118
- RS-232 Management Connection 121
- Connect Shielded RS-232 Cable 123
- Preconfigure Optional Modem 125
- Installation Summary 126
- Information and Materials 126
- Make BITS Cable (Optional) 130
- Connect BITS Cable 130
- Alarm Output Connections 131
- Wire Alarm Output Connector 132
- Alarm Input Connections 135
- Wire Alarm Input Connector 136
- DC Power Connections 139
- Wire Power Connectors 140
- Verify Wiring 141
- Dress Cables and Wires 142
- Acceptance Test 143
- Verify DSX-1 Connections 145
- Verify BITS Connection 148
- Exit Management Session 152
- Precautions 153
- Verify Software Compatibility 154
- Remove Front Cover 155
- Install Controller Card 156
- Verify Operation 157
- Replace Front Cover 158
- Install Quad T1 Framer Card 161
- Setup Summary 165
- Set Date 167
- Set Time 167
- Set System ID or CLLI code 168
- Set Gateway Address 169
- Start Management Session 171
- Management Requirements 172
- Start Management Session 173
- RS-232 Management 174
- Obtain Information 175
- Set Up Terminal Program 175
- Perform Management Operations 177
- Telnet Management 178
- Provision Access Navigator 183
- Basic Provisioning Overview 184
- Provision Access Navigator 185
- Set System ID or CLLI Code 187
- Set Ethernet Properties 189
- Set SNMP Properties 193
- Provision DCS Service 195
- DCS Provisioning Overview 196
- Provisioning ISDN BRI Service 197
- Special TR-08 Settings 199
- DCS Provisioning Quick Guide 200
- Provision DCS Service 201
- Verify Service Status 202
- Set System Clock Source 205
- Test Groom DS1 Circuits 208
- Provision and Connect DS0s 211
- Turn Up Service 213
- Test DS1 and DS0 Circuits 213
- Provision GR-303 Service 215
- GR-303 Provisioning Overview 216
- Provision GR-303 Service 217
- Provisioning P-Phone Service 218
- TR-08 Configuration 220
- Special POTS Cards 220
- Signaling Translation 220
- CRV Numbering 220
- Framing and FDL Settings 222
- Set System Switch Type 228
- Test DS1 Circuits 234
- Provision DS0s to Subscribers 244
- Test Circuits 248
- In this Chapter 249
- Pre-Provisioning and Testing 251
- Requirements 251
- Analog Interfaces 252
- Crossconnect Features 252
- FX Analog Interfaces 254
- Fractional Interfaces 255
- Remote Interfaces 256
- Provision DS0s 265
- Provision DS0 Crossconnects 267
- Test Remote Circuits 278
- ADIT 6 00 280
- FDL Management Configuration 281
- CLI Commands Descriptions 283
- Provision Drop DS0s 291
- Provision Remote Adit 600 295
- CACTUS.lite 298
- Adit 600 299
- Navigator 299
- Alarm Clearing 321
- Clear Alarms – FDL 323
- Alarm Clearing 325
- Clear Alarms – EOC 328
- Clear Alarms – SNMP 334
- Critical, Major, Minor 335
- Alarm Indicators 335
- Power Status LEDs 336
- Critical Alarm Status LEDs 338
- Major Alarm Status LEDs 338
- Minor Alarm Status LEDs 339
- Alarm Cutoff (ACO) Status LED 339
- DS1 Status LEDs 340
- Ethernet Link Status LED 341
- Alarms and Logs 344
- Alarm Reporting 345
- Alarm Testing 345
- Alarm and Status Indicators 345
- Facility Alarm System 346
- Alarm Cutoff (ACO) 346
- DS1 Failures 347
- Event Log 347
- Configuration Change Log 348
- Syntax: log bert 349
- Syntax: clear bert log 349
- Syntax: log tmc 349
- Syntax: log tmc permanent 349
- Ethernet 351
- Connector 351
- Ethernet Link OK 351
- Status Indicator 351
- Indicator Descriptions 352
- Syntax: status clock 353
- Message: 353
- Description: 353
- Example: status ds0 32:1-4 354
- Syntax: status ds1 <n> 355
- Example: status ds1 12 355
- Example: status ds1 1-4 355
- Syntax: status ds1 all 356
- Syntax: status equipment 361
- Syntax: show ip 362
- Syntax: status ip 362
- Status Remote 363
- Example: status crv 10 364
- Example: status crv 5-8 364
- Example: status isdn crv 6 365
- Example: status isdn crv 1-4 365
- Syntax: status eoc 367
- Syntax: status tmc 367
- Example: status tmc all 369
- Example: status tmc 8-12 369
- Syntax: clear peak call count 370
- Near-End Loopbacks 371
- DS1 Line Loopback 372
- DS1 Payload Loopback 372
- DS1 CSU Loopup 373
- DS1 Line Loopup 374
- DS1 Network Loopup 375
- DS1 NIU Loopup 376
- DS1 Payload Loopup 377
- Access Bank II Loopbacks 378
- Send Remote RS232 Line Loopup 379
- Send Remote T1 Payload Loopup 381
- Send Remote T1 TSI Loopup 381
- Send Remote V35 Line Loopup 383
- Bit Patterns and Error Tests 385
- Send DS1 Payload Pattern 386
- Other Maintenance Commands 395
- Technical Support 397
- Maintenance Procedures 399
- Repair and Return Procedure 400
- Replace Controller Card 401
- Verify Equipment Status 403
- Procedure Summary 404
- Verify Compatibility 405
- Controller A Controller B 407
- ALTER PROVISIONING 409
- Replace Other Controller Card 410
- Insert New Controller 414
- Maintenance Procedures 415
- Remove Old Controller 416
- Replace Quad T1 Framer Card 417
- Replace Quad T1 Card 421
- INSTALL SIMM 438
- UPDATE SOFTWARE 440
- Verify IP Connectivity 441
- Upload Configuration 441
- Download Software 442
- ANY USER 443
- Download Configuration 444
- NOT ASSIGNED TO ANY USER 449
- CLI Language Reference 457
- CLI Requirements 459
- CLI over Telnet 460
- Using CLI Command Scripts 461
- CLI Conventions and Shortcuts 462
- Text Conventions 463
- Command Syntax Descriptions 464
- Command Shortcuts (Tabbing) 465
- Keyboard Shortcuts 465
- Help System Overview 466
- Displaying Basic Commands 466
- Context Sensitive Help 467
- Syntax: print help 469
- Users and Passwords 470
- Syntax: whoami 471
- Syntax: show users 471
- Set User Password 473
- Delete User Password 473
- Delete User 473
- Logging In and Out 474
- Login with User Name Required 475
- Login with Password Required 475
- Example: set autoexit 60 476
- CLI Command List 477
- CLI Language Reference 478
- Security: Level 3 (monitor) 479
- Syntax: aco 479
- Security: Level 2 (operator) 480
- Add User 481
- Clear BERT Log 483
- Clear Blocked Call Count 483
- Clear Config Log 483
- Clear DS1 Performance 483
- Clear Log 484
- Clear Peak Call Count 484
- Clear Permanent Call Count 484
- Clear Remote Log 484
- Clear TMC Log 484
- Connect Remote Interface 487
- Delete Interface 488
- Disconnect 489
- Disconnect Remote 490
- Exit Remote Session (Ctrl+C) 490
- ON page 17-1 491
- ALL ON page 18-57) 493
- Example: log ds1 6 495
- Example: log equipment minor 495
- Example: log 495
- Log Config 497
- Example: log config 498
- Example: logon remote 12 500
- Read Remote Alarms 501
- Example: read remote 9 log 506
- Read Remote Loopback 507
- Read Remote RS232 507
- Read Remote T1 510
- Example: read remote 9 t1drop 511
- Read Remote V35 512
- Reset All 513
- Reset DS1 Framer 513
- Reset Remote 514
- Reset Standby 514
- Security: Level 1 (manager) 515
- Syntax: restore defaults 515
- Send DS1 CSU Loopup 518
- Send DS1 Line Loopup 519
- Example: set ds1 9 line p2e15 523
- Send DS1 NIU Loopup 527
- Send DS1 Payload Loopup 529
- Example: set ds1 9 down 533
- Send DS1 Off 537
- Send Remote Loopdown 537
- Send Remote RS232 TSI Loopup 539
- Send Remote T1Drop TSI Loopup 546
- Send Remote V35 TSI Loopup 549
- Send Switch Provision Request 550
- Set Alarms 551
- Set Autoexit 551
- Set Clock 552
- Example: set ds0 5:13 crv 122 555
- Set DS0 ISDN BRI CRV 557
- Set DS0 P-Phone 558
- Example: set ds0 13:1-16 up 559
- Set DS1 Clock 562
- Set DS1 FDL 562
- Set DS1 Framing 564
- Set DS1 ID 565
- Set DS1 LBO 565
- Set DS1 Line Loopup 565
- Set DS1 Linecode 566
- Set DS1 Remote Device Mgmt 569
- Set DS1 Service 570
- Set DS1 TermID 570
- Set DS1 Threshold 571
- Set Ethernet IP Address 573
- Set IP Gateway Address 574
- Example: set ip gateway none 575
- Set Remote ID 576
- Set Remote RS232 Baud 576
- Set Remote RS232 Data 577
- Set Remote RS232 Stop 577
- Set Remote T1Drop LBO 579
- Set Remote T1Drop Linecode 579
- Set Remote T1Drop PRM 580
- Set Remote V35 ClockInv 580
- Set Remote V35 CTS 581
- Set Remote V35 Data 581
- Set Remote V35 DSU 582
- Set Remote V35 RxClock 582
- Set Remote V35 Speed 582
- Set Screen 583
- Set SNMP Contact 584
- Set SNMP GetCom 584
- Set SNMP Location 585
- Set SNMP Name 585
- Set SNMP NMS Address 586
- Set SNMP SetCom 586
- Set SNMP TrapCom 587
- Set Switch Type 587
- Set User Level 589
- Show Autoexit 591
- Show Clock 591
- Show Connect 591
- Show CRV 593
- Show Date 595
- Show DS0 595
- Show DS1 596
- Syntax: show ds1 all 599
- Show EOC 601
- Show Ethernet 601
- Show Interface 602
- Show ISDN CRV 604
- Example: show isdn crv 6 605
- Example: show isdn crv 1-8 605
- Show Remote 606
- Show SNMP 609
- Show Switch 610
- Show Time 610
- Show TMC 610
- Status CRV 613
- Status DS0 614
- Status DS1 615
- Status DS1 Performance 618
- Status Equipment 624
- Example: status equipment all 625
- Status ISDN CRV 627
- TMC Status: 629
- Primary 629
- Link Status: Up 629
- Status TMC History 631
- Syntax: switch controller 632
- APPENDIX 635
- EOC Interface 637
- Managed Object Class Support 638
- Alarm Count List Objects 639
- DS1 Line Termination Objects 641
- EBS Line Termination Objects 641
- ISDN Line Termination Objects 642
- Crossconnection 644
- Equipment Objects 645
- IDLC Terminal Objects 648
- Memory Objects 648
- Network Element Objects 649
- Protection Group Objects 649
- Protection Group Unit Objects 650
- Table A-20 Action Support 651
- Notifications 652
- FDL Interface 655
- Access Bank II Capabilities 656
- Carrier Access Enterprise MIB 661
- SNMP Basics 662
- MIB Tables 663
- Managing Networks 664
- SNMP Protocols 665
- SNMP Requirements 666
- SNMP Trap Reports 667
- SNMP Interface 668
- GLOSSARY 669
- Definitions 672
- Glossary 682
- Numerics 683
Manuais e produtos relacionados com Hardware Carrier-access Access Navigator
Hardware Carrier-access 770-0015 AM Manual do Utilizador
(250 páginas)
(250 páginas)
Hardware Carrier-access Adit 3000 Series and Multi-Service Router (MSR) Ca Manual do Utilizador
(496 páginas)
(496 páginas)
Hardware Carrier-access Multi-Service Router (MSR) Card MSR/Adit 3K GUI Manual do Utilizador
(262 páginas)
(262 páginas)
Hardware Carrier-access CMG Router Manual do Utilizador
(296 páginas)
(296 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais